LeCroy Oscilloscope

MCP server for controlling LeCroy oscilloscopes via SCPI over LAN (VXI-11) or USB.

Requirements

• uv installed
• A LeCroy oscilloscope connected over LAN or USB

MCP configuration

Add to your MCP client config (e.g. Claude Code's .mcp.json):

{
  "mcpServers": {
    "lecroy-scope": {
      "type": "stdio",
      "command": "uvx",
      "args": ["lecroy-mcp"]
    }
  }
}

uvx will automatically download and run the server — no manual installation needed.

Oscilloscope setup (LAN / VXI-11)

This server communicates over the standard VXI-11 protocol. Before connecting, enable it on the scope:

1. On the scope, go to Utilities → Utilities Setup ... → Remote
2. In the Control from section, enable LXI (VXI11)
3. Note the IP Address shown — you will need it for the connection string

The scope's IP can be assigned via DHCP or configured statically under Utilities → Utility → Remote → Net Connections.

Note: The TCPIP (VICP) option shown in the same panel uses LeCroy's proprietary protocol and is currently not supported by this server. Only LXI (VXI11) is required.

Connection options

Option 1 — Manual connection

Copy the MCP client config from above as-is and connect from within the Claude session:

1. scope_scan — auto-detect LeCroy scopes on the local network
2. scope_list_resources — list all VISA resources (LAN + USB)
3. scope_connect("TCPIP0::192.168.1.111::inst0::INSTR") — connect directly

Optionally set LECROY_SUBNET to hint the scan range:

{
  "mcpServers": {
    "lecroy-scope": {
      "type": "stdio",
      "command": "uvx",
      "args": ["lecroy-mcp"],
      "env": {
        "LECROY_SUBNET": "192.168.1.0/24"
      }
    }
  }
}

Option 2 — Pre-configure the IP address (recommended for LAN)

Set LECROY_HOST in the env block and the server auto-connects on startup:

{
  "mcpServers": {
    "lecroy-scope": {
      ...
      "env": {
        "LECROY_HOST": "192.168.1.111"
      }
    }
  }
}

Option 3 — Pre-configure a full resource string (LAN or USB)

Use LECROY_RESOURCE for full control, including USB connections:

{
  "mcpServers": {
    "lecroy-scope": {
      ...
      "env": {
        "LECROY_RESOURCE": "USB0::0x05FF::0x1023::12345::INSTR"
      }
    }
  }
}

Usage

Once connected, you have tools for:

• Channel setup (scale, offset, coupling, bandwidth limit)
• Trigger configuration (mode, source, level, edge)
• Timebase and memory depth
• Automated measurements (PKPK, FREQ, RMS, RISE, DUTY, etc.)
• Waveform capture (JSON or CSV)
• Screenshots
• Math functions (FFT, INTG, DIFF, etc.)
• WaveSource built-in generator (WaveSurfer 3000Z and similar)

Supported models

The server detects the connected model and adjusts commands accordingly. Profiles are included for:

• WaveSurfer 3000Z / 4000HD
• HDO4000A / HDO6000B / HDO8000A
• WaveRunner 6000 / 8000
• WavePro HD
• MDA800A, SDA

Unknown models fall back to conservative defaults.

Manual installation

If you prefer not to use uvx:

pip install lecroy-mcp

Then use lecroy-mcp as the command in your MCP config instead of uvx lecroy-mcp.

Updating

With uvx, use the @latest tag to force the newest version:

uvx lecroy-mcp@latest

Or update the args in your .mcp.json to always pull the latest:

"args": ["lecroy-mcp@latest"]

With pip:

pip install --upgrade lecroy-mcp

Notes

• Requires pyvisa-py backend — NI-VISA is currently not supported (breaks screenshot capture)
• All VISA access is serialized via a threading lock; parallel MCP tool calls are safe

Troubleshooting

Diagnostic messages not appearing in MCP logs

If you are not seeing server log output (e.g. auto-connect status or errors) in your MCP client's log viewer, add PYTHONUNBUFFERED to the env block:

"env": {
  "PYTHONUNBUFFERED": "1"
}

This disables Python's output buffering so log messages are flushed immediately. It is not required for normal operation.

Tested with

Component	Details
Oscilloscope	Teledyne LeCroy WaveSurfer 3024Z
Operating system	Windows 10, Windows 11, Linux Mint
MCP client	Claude Code

This server should also work with other MCP-compatible clients such as OpenAI Codex and Google Gemini Code Assist, and on other operating systems such as macOS. Reports and contributions for additional configurations are welcome.

Disclaimer

Teledyne LeCroy and LeCroy are registered trademarks of Teledyne LeCroy, Inc. This project is an independent open-source tool and is not affiliated with, endorsed by, or sponsored by Teledyne LeCroy, Inc. All product and company names are trademarks or registered trademarks of their respective holders.