Rs3005p

An MCP server that lets AI agents control an RS PRO RS-3005P (or RS-6005P) digital programmable DC power supply over its USB / RS232 serial interface.

It implements the documented RS Series Remote Control Syntax V2.0 (KORAD-compatible) and exposes voltage/current control, live measurements, output and over-current-protection switching, and panel-memory save/recall as MCP tools.

Supported hardware

Model	Voltage	Current	Remote interface
RS-3005P	0–30 V	0–5 A	USB + RS232
RS-6005P	0–60 V	0–5 A	USB + RS232

The non-P variants (RS-3005D / RS-6005D) have no remote interface and cannot be driven by this server.

Serial settings (fixed by the firmware): 9600 baud, 8 data bits, no parity, 1 stop bit, no flow control.

Install

uv venv
uv pip install -e .

Run

The server speaks MCP over stdio:

uv run rs3005p-mcp

Claude Code / Claude Desktop config

{
  "mcpServers": {
    "rs3005p": {
      "command": "uv",
      "args": ["run", "rs3005p-mcp"],
      "cwd": "C:/path/to/rs3005p-mcp"
    }
  }
}

Tools

Tool	Purpose
list_serial_ports	Discover the COM/tty port the supply is on.
connect	Open the port, pick the model, verify with *IDN?.
disconnect	Close the connection.
get_identification	Read the *IDN? string.
get_safety_profile	Read the active safety envelope (read-only).
list_devices	List device profiles in the library + which is active.
select_device	Switch active profile (widening needs confirm_widen).
set_voltage	Set the voltage setpoint (range + safety validated).
set_current	Set the current limit (range + safety validated).
ramp_voltage	Ramp voltage to a target within the slew limit.
power_up	Bring the DUT to its profile's nominal operating point.
get_setpoints	Read configured voltage & current setpoints.
measure	Read actual output voltage & current.
set_output	Enable/disable the output terminals.
set_ocp	Arm/disarm over-current protection.
get_status	Decoded status: output, CV/CC mode, OCP.
get_state	Full snapshot (setpoints + measurements + status).
save_settings	Store panel settings to memory slot 1–5.
recall_settings	Recall panel settings from memory slot 1–5.

Safety profiles (protecting attached devices)

To stop an agent from over-driving the device wired to the terminals, supply a device-profile library at launch. It defines a safe envelope (voltage / current / power ceilings, output gating, slew limit) per device; the server rejects any agent request that would leave it. Profiles are set by the operator at startup and cannot be changed by any tool.

rs3005p-mcp --profile devices.json --device 24v-sensor

RS3005P_DEVICE/--device is only the default; an agent can switch among the curated devices at runtime with select_device (widening the envelope requires confirm_widen=true) and devices.json edits hot-reload on the next connect/select_device — no re-registration. No tool can create or modify a profile's limits; the file stays operator-curated.

See docs/safety.md and examples/devices.example.json. With no profile the server runs limited only by hardware (30 V / 5 A) and says so on every connect.

A typical agent flow:

1. list_serial_ports → find the port.
2. connect(port="COM4") → verifies identity, applies RS-3005P limits.
3. set_voltage(5.0), set_current(0.5).
4. set_output(True).
5. measure() → live readings.

Development

uv pip install -e ".[dev]"
uv run pytest

Tests run against an in-memory device emulator (tests/conftest.py), so no hardware is required. See docs/ for the protocol reference and architecture notes.

License

MIT.